Frequently Asked Questions
Please check out our Frequently Asked Questions to find helpful answers and information about American Road Patch.
American Road Patch is a high-quality asphalt, polymer and geo synthetic fiberglass reinforced patch. This patch was developed using a unique patented technology and works by embedding into the roadway forming a waterproof seal. Unlike traditional methods, American Road Patch properly contains, strengthens, and seals potholes, cracks, and utility cut repairs. A key benefit to this product is that it is simple to apply and does not require special vehicles or equipment. Therefore, the physical construction area is confined with very limited traffic interruption.
The Company based in Cheshire, UK is the exclusive sole importer and distributor of the American Road Patch into the UK and the Republic of Ireland.
The Team recognised the valuable contribution American Road Patch has brough to the USA pothole repair industry, a product which will significantly reduce the failures by significantly extending the life of pothole repairs in the UK and Republic of Ireland, reducing the necessity for repeat repairs, repeat repair costs, deaths and personal injuries, vehicle collateral damage costs and of course reducing the carbon footprint.
Reduced time to the exposure to potholes does increase road safety whilst reducing insurance costs for local authorities and motorists.
American Road Patch is designed to cover the whole repair and bond to the existing intact surrounding roadway or pavement, encapsulating and producing an extremely durable mechanical and waterproof barrier.
It is suitable for the following:
- Pothole Repair
Asphalt or concrete crack sealing and preservation
Man-hole surround sealing
Utility-cut sealing
Sealing around water utility lids
Low spot fill-in repairs
Seals alligatored asphalt
Repair of uneven bridge joints
Speed Bumps
Roadway Traction
American Road Patch has been installed on pavements throughout the US, performing through multiple seasons, freeze-thaw cycles, ice, and snow. When specific guidelines and instructions are followed, we have not seen snow plows dislodge the patches. American Road Patch is not indestructible but is incredibly durable when applied properly.
There is no specialized equipment required to install American Road Patch and no specific training needed. Application instructions are available with each roll.
American Road Patch works well with hot asphalt and all types of cold patch products.
American Road Patch should not be installed in rain, snow or icy conditions as the pavement surface needs to be clean and dry for proper adhesion.
The roadway can be opened to traffic immediately after installation. Traffic enhances the embedment of American Road Patch because it is designed to become part of the pavement.
Gassing or the lack of gassing has no effect on American Road Patch itself.
Repair time on average takes 10-20 minutes, depending on the type and size of the repair.
Not at this time.
The synthetic aggregate surface of American Road Patch is similar to that of a traditional Chipseal surface treatment and provides adequate friction for traffic. The surface will wear similarly to that of a Chipseal surface and provide several years of wearing surface.
Yes, a 3” overlap is recommended whenever an irregular or a large repair is required.
Average roll weight is 70 lbs.
Approximately 69 square feet per roll.
The average thickness is 1/8” – 3/16”.
Please check with your local distributor.
Some examples of primers are: Carlisle CCW–702 WB, Carlisle CCW–715 (must dry before applying American Road Patch), Henry HE203–Roll Roofing Adhesive. Be sure to follow the primer manufacturer instructions as stated on each individual product.
Yes, once installed American Road Patch can be sealed with driveway sealer, slurry seal, or Chipseal.
Using a utility knife, it is recommended to cut from the bottom or release paper side as it will cut cleaner through the bitumen and aggregate.
Yes, American Road Patch will mill up with pavement milling operations.
It is acceptable to lightly heat the top (aggregate surface) of the patch to soften the bitumen before embedment. Apply torch 8” – 12” away, constantly moving the torch evenly over the surface, as to avoid burning or melting the surface. Holding the torch in one place will melt the surface.
Do not heat or torch the bottom (bitumen side) of the patch. Doing so may result in damage to the bitumen preventing it from installing properly. It is best to heat the pavement directly in front of the patch as the patch is placed on the pavement, as noted in the instructions.
If a patch does not adequately embed into the pavement or peels up after installation – either completely or partially – it does not mean the patch cannot be used. Pull up the patch, or cut out the section that did not adhere properly, clean and remove any dust and debris, dry the patch material and reapply following the installation instructions. It may not be necessary to remove the entire patch.
American Road PatchTM
Please click below to download the Installation Guide on how to install American Road Patch.
